Hello everybody.Firstly, I must apologise to all those who have purchased these instructions from me over the past few months.From May this year, Ebay revised their Downloadable Media Policy & decided to ban all digitally delivered items. This meant that the instructions that I have been successfully emailing to people were now banned from being delivered by email. I could have elected to print each set out & post them to buyers, but to be perfectly honest this would be both time consuming & an unnecessary use of resources (printer ink, paper, envelopes etc.) so I decided to simply stop listing in order to be a good boy & comply with the policies.Unfortunately, not all members are as good at sticking to the rules as myself & several are still listing on a nudge, nudge, wink, wink, 'I won’t actually state that I email the instructions even though I do' basis.
This guide is dedicated to these members.It would seem that the only way to make sure everybody sticks to the rules is to make sure that the information is made available to all, so rather than paying for the instructions to be emailed, here they are for free:106 PLIP PROGRAMMINGProcedure1. Unlock the vehicle using the working key.2. Press the LOCK button 2 times within 20 seconds.206 PLIP PROGRAMMINGCENTRAL DOOR LOCK (1 BUTTON PLIP KEY)Procedure1. Ensure all doors are unlocked using the key.2.
Press and hold plip key button until LED stops flashing.3. After releasing button, LED will light constantly.4. Press the Plip Button once, and LED will extinguish.5. Open the door and hold the Plip key near the Ignition switch, and press the plip button one time.6. Turn the ignition ON, and wait 10 seconds then turn ignition OFF.7. After 5 seconds, Plip should now operate.CENTRAL DOOR LOCK with DEADLOCKING (2 BUTTON PLIP KEY)Procedure1.
Ensure all doors are unlocked using the key.2. Press and HOLD the large plip key button while the LED flashes continuously for 20 seconds. After 20 seconds press the small deadlock button once while still holding the large button.3.
The LED will stop flashing.4. Release the large button and the LED will light constantly.5. Press the large button one time, and the LED will go out.6. Open the door and hold the Plip key near the Ignition switch, and press the large plip button one time.7.
Turn the ignition ON, and wait 10 seconds then turn ignition OFF.8. After 5 seconds, Plip should now operate.306 & 806 (1998-) PLIP PROGRAMMINGProcedure1. Turn the Ignition switch to accessory position using the key, without the remote plip attached.2. Hold the Plip key close to the central locking receiver mounted in the roof console.3. Press the large plip button, then the small plip button on the remote.4. Repeat for second Plip key if required.5.
Turn ignition OFF.6. After 5 seconds, Plip should now operate.406, 405 & 605 PLIP PROGRAMMINGThe 406 deadlocking remote control has specific button controls, and if the vehicles has two controls, one is set as primary and the other as secondary.When replacing the Plip, a Primary or Secondary Plip are different part numbers and must be ordered as required. The white label inside the Plip is labelled PRIM and SEC.Procedure1. Turn the Ignition switch ON.2.
Press the large Plip key button (Primary Plip)3. Within 10 seconds, press the large Plip key button (Secondary Plip)4. If there is one remote, press the Primary plip button twice.5. Turn ignition OFF.6. Test Plip’s for correct operation.NOTE: On some 406 models, Plips cannot be re-synchronised unless the battery has been disconnected for 1 minute.806 (-1998) PLIP PROGRAMMINGProcedure1. Turn the Ignition switch to accessory position using the key, without the remote plip attached.2.
Hold the Plip key towards the receiver at the front of the vehicle.3. Press the large plip button, then the small plip button on the remote.4. Repeat for second Plip key if required.5. Turn ignition OFF.6.
Remote Key Fob Replacement
After 5 seconds, Plip should now operate.307 PLIP PROGRAMMINGProcedure1. Turn the Ignition switch to ON position using the first key.2. Press the LOCK button for 10 seconds.3. Remove key and wait for 10 seconds.4. Check Plip key operation.5. Repeat for second Plip key if required.6.
Turn ignition OFF206 PLIP PROGRAMMING SYNCHRONISATION—BSIProcedure1. Insert Ignition Key.2. Press the small Black button.3. Switch the Ignition ON4. Keep the lock button pressed for 10 seconds.5. Release lock button, switch ignition OFF and remove key.6.
407 Peugeot 2007 Parts
Close all doors and press the lock button 2 times.NOTE: If Plips still do not work, start the vehicle and then turn OFF. Open and close the door, and check Plip again. This is also necessary after a new BSI system is fitted.
Peugeot 407 Remote Key Not Working 2017
IMPORTANT: PLEASE REPEAT STEPS IF NOT WORKING.You need to tune your key fob into your cars alarm system.